Author : Ila Mulyandi1 comment
Library Adafruit FONA sendiri sebetulnya di desain untuk module SIMCOM SIM800 dan SIM808 namun karena Chip SIM800L ini adalah versi "Lite" dari SIM800 jadi masih banyak kesamaan dari kedua chip,hanya saja pada SIM800L/800Lite tidak dibekali fitur FM RADIO,BLUETOOTH seperti apalagi fitur GPS seperti SIM800 dan SIM808.
Sebelum melakukan Explore All Fuction pada SIM800L V.2 (ataupun V.1) mari kita siapkan dulu file dan wiring berikut :
Hardware SIM800L V.2 dapat debeli dengan harga MURAH disini
1.File Library
Library Adafruit_FONA download disini
Ekstract kemudian masukan kedua library diatas kedalam folder libraries pada folder installer software Arduino IDE (C:\Program Files\Arduino\libraries atau C:\Program Files (X86)\Arduino\libraries bagi pengguna Win64 bit)
2.Wiring
Sambungkan Module SIM800L dengan Arduino (disini saya menggunakan UNO)
SIM800L V.2
5VIN <--> pin 5V Arduino
GND <--> pin GND Arduino
RXD <--> pin D2 Arduino
TXD <--> pin D3 Arduino
RST <--> pin D4 Arduino
SIM800L V.1
VCC <--> 3.7-4.2VDC melalui stepdown dari pin 5V Arduino
GND <--> pin GND Arduino
RXD <--> pin D2 Arduino
TXD <--> pin D3 Arduino
RST <--> pin D4 Arduino
2.Sketch Coding
Copy paste sketch dibawah ini ke dalam Arduino IDE kemudian Upload ke dalam Arduino
#include "Adafruit_FONA.h"
#define FONA_RX 2
#define FONA_TX 3
#define FONA_RST 4
// this is a large buffer for replies
char replybuffer[255];
// We default to using software serial. If you want to use hardware serial
// (because softserial isnt supported) comment out the following three lines
// and uncomment the HardwareSerial line
#include <SoftwareSerial.h>
SoftwareSerial fonaSS = SoftwareSerial(FONA_TX, FONA_RX);
SoftwareSerial *fonaSerial = &fonaSS;
// Hardware serial is also possible!
// HardwareSerial *fonaSerial = &Serial1;
// Use this for FONA 800 and 808s
Adafruit_FONA fona = Adafruit_FONA(FONA_RST);
// Use this one for FONA 3G
//Adafruit_FONA_3G fona = Adafruit_FONA_3G(FONA_RST);
uint8_t readline(char *buff, uint8_t maxbuff, uint16_t timeout = 0);
uint8_t type;
void setup() {
while (!Serial);
Serial.begin(115200);
Serial.println(F("FONA basic test"));
Serial.println(F("Initializing....(May take 3 seconds)"));
fonaSerial->begin(4800);
if (! fona.begin(*fonaSerial)) {
Serial.println(F("Couldn't find FONA"));
while (1);
}
type = fona.type();
Serial.println(F("FONA is OK"));
Serial.print(F("Found "));
switch (type) {
case FONA800L:
Serial.println(F("FONA 800L")); break;
case FONA800H:
Serial.println(F("FONA 800H")); break;
case FONA808_V1:
Serial.println(F("FONA 808 (v1)")); break;
case FONA808_V2:
Serial.println(F("FONA 808 (v2)")); break;
case FONA3G_A:
Serial.println(F("FONA 3G (American)")); break;
case FONA3G_E:
Serial.println(F("FONA 3G (European)")); break;
default:
Serial.println(F("???")); break;
}
// Print module IMEI number.
char imei[15] = {0}; // MUST use a 16 character buffer for IMEI!
uint8_t imeiLen = fona.getIMEI(imei);
if (imeiLen > 0) {
Serial.print("Module IMEI: "); Serial.println(imei);
}
// Optionally configure a GPRS APN, username, and password.
// You might need to do this to access your network's GPRS/data
// network. Contact your provider for the exact APN, username,
// and password values. Username and password are optional and
// can be removed, but APN is required.
//fona.setGPRSNetworkSettings(F("your APN"), F("your username"), F("your password"));
// Optionally configure HTTP gets to follow redirects over SSL.
// Default is not to follow SSL redirects, however if you uncomment
// the following line then redirects over SSL will be followed.
//fona.setHTTPSRedirect(true);
printMenu();
}
void printMenu(void) {
Serial.println(F("-------------------------------------"));
Serial.println(F("[?] Print this menu"));
Serial.println(F("[a] read the ADC 2.8V max (FONA800 & 808)"));
Serial.println(F("[b] read the Battery V and % charged"));
Serial.println(F("[C] read the SIM CCID"));
Serial.println(F("[U] Unlock SIM with PIN code"));
Serial.println(F("[i] read RSSI"));
Serial.println(F("[n] get Network status"));
Serial.println(F("[v] set audio Volume"));
Serial.println(F("[V] get Volume"));
Serial.println(F("[H] set Headphone audio (FONA800 & 808)"));
Serial.println(F("[e] set External audio (FONA800 & 808)"));
Serial.println(F("[T] play audio Tone"));
Serial.println(F("[P] PWM/Buzzer out (FONA800 & 808)"));
// FM (SIM800 only!)
Serial.println(F("[f] tune FM radio (FONA800)"));
Serial.println(F("[F] turn off FM (FONA800)"));
Serial.println(F("[m] set FM volume (FONA800)"));
Serial.println(F("[M] get FM volume (FONA800)"));
Serial.println(F("[q] get FM station signal level (FONA800)"));
// Phone
Serial.println(F("[c] make phone Call"));
Serial.println(F("[A] get call status"));
Serial.println(F("[h] Hang up phone"));
Serial.println(F("[p] Pick up phone"));
// SMS
Serial.println(F("[N] Number of SMSs"));
Serial.println(F("[r] Read SMS #"));
Serial.println(F("[R] Read All SMS"));
Serial.println(F("[d] Delete SMS #"));
Serial.println(F("[s] Send SMS"));
Serial.println(F("[u] Send USSD"));
// Time
Serial.println(F("[y] Enable network time sync (FONA 800 & 808)"));
Serial.println(F("[Y] Enable NTP time sync (GPRS FONA 800 & 808)"));
Serial.println(F("[t] Get network time"));
// GPRS
Serial.println(F("[G] Enable GPRS"));
Serial.println(F("[g] Disable GPRS"));
Serial.println(F("[l] Query GSMLOC (GPRS)"));
Serial.println(F("[w] Read webpage (GPRS)"));
Serial.println(F("[W] Post to website (GPRS)"));
// GPS
if ((type == FONA3G_A) || (type == FONA3G_E) || (type == FONA808_V1) || (type == FONA808_V2)) {
Serial.println(F("[O] Turn GPS on (FONA 808 & 3G)"));
Serial.println(F("[o] Turn GPS off (FONA 808 & 3G)"));
Serial.println(F("[L] Query GPS location (FONA 808 & 3G)"));
if (type == FONA808_V1) {
Serial.println(F("[x] GPS fix status (FONA808 v1 only)"));
}
Serial.println(F("[E] Raw NMEA out (FONA808)"));
}
Serial.println(F("[S] create Serial passthru tunnel"));
Serial.println(F("-------------------------------------"));
Serial.println(F(""));
}
void loop() {
Serial.print(F("FONA> "));
while (! Serial.available() ) {
if (fona.available()) {
Serial.write(fona.read());
}
}
char command = Serial.read();
Serial.println(command);
switch (command) {
case '?': {
printMenu();
break;
}
case 'a': {
// read the ADC
uint16_t adc;
if (! fona.getADCVoltage(&adc)) {
Serial.println(F("Failed to read ADC"));
} else {
Serial.print(F("ADC = ")); Serial.print(adc); Serial.println(F(" mV"));
}
break;
}
case 'b': {
// read the battery voltage and percentage
uint16_t vbat;
if (! fona.getBattVoltage(&vbat)) {
Serial.println(F("Failed to read Batt"));
} else {
Serial.print(F("VBat = ")); Serial.print(vbat); Serial.println(F(" mV"));
}
if (! fona.getBattPercent(&vbat)) {
Serial.println(F("Failed to read Batt"));
} else {
Serial.print(F("VPct = ")); Serial.print(vbat); Serial.println(F("%"));
}
break;
}
case 'U': {
// Unlock the SIM with a PIN code
char PIN[5];
flushSerial();
Serial.println(F("Enter 4-digit PIN"));
readline(PIN, 3);
Serial.println(PIN);
Serial.print(F("Unlocking SIM card: "));
if (! fona.unlockSIM(PIN)) {
Serial.println(F("Failed"));
} else {
Serial.println(F("OK!"));
}
break;
}
case 'C': {
// read the CCID
fona.getSIMCCID(replybuffer); // make sure replybuffer is at least 21 bytes!
Serial.print(F("SIM CCID = ")); Serial.println(replybuffer);
break;
}
case 'i': {
// read the RSSI
uint8_t n = fona.getRSSI();
int8_t r;
Serial.print(F("RSSI = ")); Serial.print(n); Serial.print(": ");
if (n == 0) r = -115;
if (n == 1) r = -111;
if (n == 31) r = -52;
if ((n >= 2) && (n <= 30)) {
r = map(n, 2, 30, -110, -54);
}
Serial.print(r); Serial.println(F(" dBm"));
break;
}
case 'n': {
// read the network/cellular status
uint8_t n = fona.getNetworkStatus();
Serial.print(F("Network status "));
Serial.print(n);
Serial.print(F(": "));
if (n == 0) Serial.println(F("Not registered"));
if (n == 1) Serial.println(F("Registered (home)"));
if (n == 2) Serial.println(F("Not registered (searching)"));
if (n == 3) Serial.println(F("Denied"));
if (n == 4) Serial.println(F("Unknown"));
if (n == 5) Serial.println(F("Registered roaming"));
break;
}
/*** Audio ***/
case 'v': {
// set volume
flushSerial();
if ( (type == FONA3G_A) || (type == FONA3G_E) ) {
Serial.print(F("Set Vol [0-8] "));
} else {
Serial.print(F("Set Vol % [0-100] "));
}
uint8_t vol = readnumber();
Serial.println();
if (! fona.setVolume(vol)) {
Serial.println(F("Failed"));
} else {
Serial.println(F("OK!"));
}
break;
}
case 'V': {
uint8_t v = fona.getVolume();
Serial.print(v);
if ( (type == FONA3G_A) || (type == FONA3G_E) ) {
Serial.println(" / 8");
} else {
Serial.println("%");
}
break;
}
case 'H': {
// Set Headphone output
if (! fona.setAudio(FONA_HEADSETAUDIO)) {
Serial.println(F("Failed"));
} else {
Serial.println(F("OK!"));
}
fona.setMicVolume(FONA_HEADSETAUDIO, 15);
break;
}
case 'e': {
// Set External output
if (! fona.setAudio(FONA_EXTAUDIO)) {
Serial.println(F("Failed"));
} else {
Serial.println(F("OK!"));
}
fona.setMicVolume(FONA_EXTAUDIO, 10);
break;
}
case 'T': {
// play tone
flushSerial();
Serial.print(F("Play tone #"));
uint8_t kittone = readnumber();
Serial.println();
// play for 1 second (1000 ms)
if (! fona.playToolkitTone(kittone, 1000)) {
Serial.println(F("Failed"));
} else {
Serial.println(F("OK!"));
}
break;
}
/*** FM Radio ***/
case 'f': {
// get freq
flushSerial();
Serial.print(F("FM Freq (eg 1011 == 101.1 MHz): "));
uint16_t station = readnumber();
Serial.println();
// FM radio ON using headset
if (fona.FMradio(true, FONA_HEADSETAUDIO)) {
Serial.println(F("Opened"));
}
if (! fona.tuneFMradio(station)) {
Serial.println(F("Failed"));
} else {
Serial.println(F("Tuned"));
}
break;
}
case 'F': {
// FM radio off
if (! fona.FMradio(false)) {
Serial.println(F("Failed"));
} else {
Serial.println(F("OK!"));
}
break;
}
case 'm': {
// Set FM volume.
flushSerial();
Serial.print(F("Set FM Vol [0-6]:"));
uint8_t vol = readnumber();
Serial.println();
if (!fona.setFMVolume(vol)) {
Serial.println(F("Failed"));
} else {
Serial.println(F("OK!"));
}
break;
}
case 'M': {
// Get FM volume.
uint8_t fmvol = fona.getFMVolume();
if (fmvol < 0) {
Serial.println(F("Failed"));
} else {
Serial.print(F("FM volume: "));
Serial.println(fmvol, DEC);
}
break;
}
case 'q': {
// Get FM station signal level (in decibels).
flushSerial();
Serial.print(F("FM Freq (eg 1011 == 101.1 MHz): "));
uint16_t station = readnumber();
Serial.println();
int8_t level = fona.getFMSignalLevel(station);
if (level < 0) {
Serial.println(F("Failed! Make sure FM radio is on (tuned to station)."));
} else {
Serial.print(F("Signal level (dB): "));
Serial.println(level, DEC);
}
break;
}
/*** PWM ***/
case 'P': {
// PWM Buzzer output @ 2KHz max
flushSerial();
Serial.print(F("PWM Freq, 0 = Off, (1-2000): "));
uint16_t freq = readnumber();
Serial.println();
if (! fona.setPWM(freq)) {
Serial.println(F("Failed"));
} else {
Serial.println(F("OK!"));
}
break;
}
/*** Call ***/
case 'c': {
// call a phone!
char number[30];
flushSerial();
Serial.print(F("Call #"));
readline(number, 30);
Serial.println();
Serial.print(F("Calling ")); Serial.println(number);
if (!fona.callPhone(number)) {
Serial.println(F("Failed"));
} else {
Serial.println(F("Sent!"));
}
break;
}
case 'A': {
// get call status
int8_t callstat = fona.getCallStatus();
switch (callstat) {
case 0: Serial.println(F("Ready")); break;
case 1: Serial.println(F("Could not get status")); break;
case 3: Serial.println(F("Ringing (incoming)")); break;
case 4: Serial.println(F("Ringing/in progress (outgoing)")); break;
default: Serial.println(F("Unknown")); break;
}
break;
}
case 'h': {
// hang up!
if (! fona.hangUp()) {
Serial.println(F("Failed"));
} else {
Serial.println(F("OK!"));
}
break;
}
case 'p': {
// pick up!
if (! fona.pickUp()) {
Serial.println(F("Failed"));
} else {
Serial.println(F("OK!"));
}
break;
}
/*** SMS ***/
case 'N': {
// read the number of SMS's!
int8_t smsnum = fona.getNumSMS();
if (smsnum < 0) {
Serial.println(F("Could not read # SMS"));
} else {
Serial.print(smsnum);
Serial.println(F(" SMS's on SIM card!"));
}
break;
}
case 'r': {
// read an SMS
flushSerial();
Serial.print(F("Read #"));
uint8_t smsn = readnumber();
Serial.print(F("\n\rReading SMS #")); Serial.println(smsn);
// Retrieve SMS sender address/phone number.
if (! fona.getSMSSender(smsn, replybuffer, 250)) {
Serial.println("Failed!");
break;
}
Serial.print(F("FROM: ")); Serial.println(replybuffer);
// Retrieve SMS value.
uint16_t smslen;
if (! fona.readSMS(smsn, replybuffer, 250, &smslen)) { // pass in buffer and max len!
Serial.println("Failed!");
break;
}
Serial.print(F("***** SMS #")); Serial.print(smsn);
Serial.print(" ("); Serial.print(smslen); Serial.println(F(") bytes *****"));
Serial.println(replybuffer);
Serial.println(F("*****"));
break;
}
case 'R': {
// read all SMS
int8_t smsnum = fona.getNumSMS();
uint16_t smslen;
int8_t smsn;
if ( (type == FONA3G_A) || (type == FONA3G_E) ) {
smsn = 0; // zero indexed
smsnum--;
} else {
smsn = 1; // 1 indexed
}
for ( ; smsn <= smsnum; smsn++) {
Serial.print(F("\n\rReading SMS #")); Serial.println(smsn);
if (!fona.readSMS(smsn, replybuffer, 250, &smslen)) { // pass in buffer and max len!
Serial.println(F("Failed!"));
break;
}
// if the length is zero, its a special case where the index number is higher
// so increase the max we'll look at!
if (smslen == 0) {
Serial.println(F("[empty slot]"));
smsnum++;
continue;
}
Serial.print(F("***** SMS #")); Serial.print(smsn);
Serial.print(" ("); Serial.print(smslen); Serial.println(F(") bytes *****"));
Serial.println(replybuffer);
Serial.println(F("*****"));
}
break;
}
case 'd': {
// delete an SMS
flushSerial();
Serial.print(F("Delete #"));
uint8_t smsn = readnumber();
Serial.print(F("\n\rDeleting SMS #")); Serial.println(smsn);
if (fona.deleteSMS(smsn)) {
Serial.println(F("OK!"));
} else {
Serial.println(F("Couldn't delete"));
}
break;
}
case 's': {
// send an SMS!
char sendto[21], message[141];
flushSerial();
Serial.print(F("Send to #"));
readline(sendto, 20);
Serial.println(sendto);
Serial.print(F("Type out one-line message (140 char): "));
readline(message, 140);
Serial.println(message);
if (!fona.sendSMS(sendto, message)) {
Serial.println(F("Failed"));
} else {
Serial.println(F("Sent!"));
}
break;
}
case 'u': {
// send a USSD!
char message[141];
flushSerial();
Serial.print(F("Type out one-line message (140 char): "));
readline(message, 140);
Serial.println(message);
uint16_t ussdlen;
if (!fona.sendUSSD(message, replybuffer, 250, &ussdlen)) { // pass in buffer and max len!
Serial.println(F("Failed"));
} else {
Serial.println(F("Sent!"));
Serial.print(F("***** USSD Reply"));
Serial.print(" ("); Serial.print(ussdlen); Serial.println(F(") bytes *****"));
Serial.println(replybuffer);
Serial.println(F("*****"));
}
}
/*** Time ***/
case 'y': {
// enable network time sync
if (!fona.enableNetworkTimeSync(true))
Serial.println(F("Failed to enable"));
break;
}
case 'Y': {
// enable NTP time sync
if (!fona.enableNTPTimeSync(true, F("pool.ntp.org")))
Serial.println(F("Failed to enable"));
break;
}
case 't': {
// read the time
char buffer[23];
fona.getTime(buffer, 23); // make sure replybuffer is at least 23 bytes!
Serial.print(F("Time = ")); Serial.println(buffer);
break;
}
/*********************************** GPS (SIM808 only) */
case 'o': {
// turn GPS off
if (!fona.enableGPS(false))
Serial.println(F("Failed to turn off"));
break;
}
case 'O': {
// turn GPS on
if (!fona.enableGPS(true))
Serial.println(F("Failed to turn on"));
break;
}
case 'x': {
int8_t stat;
// check GPS fix
stat = fona.GPSstatus();
if (stat < 0)
Serial.println(F("Failed to query"));
if (stat == 0) Serial.println(F("GPS off"));
if (stat == 1) Serial.println(F("No fix"));
if (stat == 2) Serial.println(F("2D fix"));
if (stat == 3) Serial.println(F("3D fix"));
break;
}
case 'L': {
// check for GPS location
char gpsdata[120];
fona.getGPS(0, gpsdata, 120);
if (type == FONA808_V1)
Serial.println(F("Reply in format: mode,longitude,latitude,altitude,utctime(yyyymmddHHMMSS),ttff,satellites,speed,course"));
else
Serial.println(F("Reply in format: mode,fixstatus,utctime(yyyymmddHHMMSS),latitude,longitude,altitude,speed,course,fixmode,reserved1,HDOP,PDOP,VDOP,reserved2,view_satellites,used_satellites,reserved3,C/N0max,HPA,VPA"));
Serial.println(gpsdata);
break;
}
case 'E': {
flushSerial();
if (type == FONA808_V1) {
Serial.print(F("GPS NMEA output sentences (0 = off, 34 = RMC+GGA, 255 = all)"));
} else {
Serial.print(F("On (1) or Off (0)? "));
}
uint8_t nmeaout = readnumber();
// turn on NMEA output
fona.enableGPSNMEA(nmeaout);
break;
}
/*********************************** GPRS */
case 'g': {
// turn GPRS off
if (!fona.enableGPRS(false))
Serial.println(F("Failed to turn off"));
break;
}
case 'G': {
// turn GPRS on
if (!fona.enableGPRS(true))
Serial.println(F("Failed to turn on"));
break;
}
case 'l': {
// check for GSMLOC (requires GPRS)
uint16_t returncode;
if (!fona.getGSMLoc(&returncode, replybuffer, 250))
Serial.println(F("Failed!"));
if (returncode == 0) {
Serial.println(replybuffer);
} else {
Serial.print(F("Fail code #")); Serial.println(returncode);
}
break;
}
case 'w': {
// read website URL
uint16_t statuscode;
int16_t length;
char url[80];
flushSerial();
Serial.println(F("NOTE: in beta! Use small webpages to read!"));
Serial.println(F("URL to read (e.g. www.adafruit.com/testwifi/index.html):"));
Serial.print(F("http://")); readline(url, 79);
Serial.println(url);
Serial.println(F("****"));
if (!fona.HTTP_GET_start(url, &statuscode, (uint16_t *)&length)) {
Serial.println("Failed!");
break;
}
while (length > 0) {
while (fona.available()) {
char c = fona.read();
// Serial.write is too slow, we'll write directly to Serial register!
#if defined(__AVR_ATmega328P__) || defined(__AVR_ATmega168__)
loop_until_bit_is_set(UCSR0A, UDRE0); /* Wait until data register empty. */
UDR0 = c;
#else
Serial.write(c);
#endif
length--;
if (! length) break;
}
}
Serial.println(F("\n****"));
fona.HTTP_GET_end();
break;
}
case 'W': {
// Post data to website
uint16_t statuscode;
int16_t length;
char url[80];
char data[80];
flushSerial();
Serial.println(F("NOTE: in beta! Use simple websites to post!"));
Serial.println(F("URL to post (e.g. httpbin.org/post):"));
Serial.print(F("http://")); readline(url, 79);
Serial.println(url);
Serial.println(F("Data to post (e.g. \"foo\" or \"{\"simple\":\"json\"}\"):"));
readline(data, 79);
Serial.println(data);
Serial.println(F("****"));
if (!fona.HTTP_POST_start(url, F("text/plain"), (uint8_t *) data, strlen(data), &statuscode, (uint16_t *)&length)) {
Serial.println("Failed!");
break;
}
while (length > 0) {
while (fona.available()) {
char c = fona.read();
#if defined(__AVR_ATmega328P__) || defined(__AVR_ATmega168__)
loop_until_bit_is_set(UCSR0A, UDRE0); /* Wait until data register empty. */
UDR0 = c;
#else
Serial.write(c);
#endif
length--;
if (! length) break;
}
}
Serial.println(F("\n****"));
fona.HTTP_POST_end();
break;
}
/*****************************************/
case 'S': {
Serial.println(F("Creating SERIAL TUBE"));
while (1) {
while (Serial.available()) {
delay(1);
fona.write(Serial.read());
}
if (fona.available()) {
Serial.write(fona.read());
}
}
break;
}
default: {
Serial.println(F("Unknown command"));
printMenu();
break;
}
}
// flush input
flushSerial();
while (fona.available()) {
Serial.write(fona.read());
}
}
void flushSerial() {
while (Serial.available())
Serial.read();
}
char readBlocking() {
while (!Serial.available());
return Serial.read();
}
uint16_t readnumber() {
uint16_t x = 0;
char c;
while (! isdigit(c = readBlocking())) {
//Serial.print(c);
}
Serial.print(c);
x = c - '0';
while (isdigit(c = readBlocking())) {
Serial.print(c);
x *= 10;
x += c - '0';
}
return x;
}
uint8_t readline(char *buff, uint8_t maxbuff, uint16_t timeout) {
uint16_t buffidx = 0;
boolean timeoutvalid = true;
if (timeout == 0) timeoutvalid = false;
while (true) {
if (buffidx > maxbuff) {
//Serial.println(F("SPACE"));
break;
}
while (Serial.available()) {
char c = Serial.read();
//Serial.print(c, HEX); Serial.print("#"); Serial.println(c);
if (c == '\r') continue;
if (c == 0xA) {
if (buffidx == 0) // the first 0x0A is ignored
continue;
timeout = 0; // the second 0x0A is the end of the line
timeoutvalid = true;
break;
}
buff[buffidx] = c;
buffidx++;
}
if (timeoutvalid && timeout == 0) {
//Serial.println(F("TIMEOUT"));
break;
}
delay(1);
}
buff[buffidx] = 0; // null term
return buffidx;
}
xxSetelah Upload Sketch diatas Buka Serial Monitor pada Arduino IDE dengan Baudrate 115200 - Newline
Pastikan anda sudah memasukan SIM Card GSM ke dalam module dan minimal ada pulsanya untuk test kirim SMS dan Telefon.
3.Function & Menu Interface
Berikut adalah Menu yang dapat kita Gunakan untuk Explore fungsi dari Module SIM800L
Beberapa menu yang berhubungan dengan Bluetooth,FM Radio dan GPS tidak dapat kita gunakan jadi tidak usah dicoba,tapi kalau penasaran ya silahkan dicoba aja.
-------------------------------------
[?] Print this menu --> menampilkan menu perintah ini ke serial monitor
[a] read the ADC 2.8V max (FONA800 & 808) --> membaca tegangan ADC pada Module
[b] read the Battery V and % charged -->membaca Tegangan dan persentase Battery
[C] read the SIM CCID -->membaca SSID dari Sim Card
[U] Unlock SIM with PIN code -->membuka kode PIN dari SIM (apabila status terkunci)
[i] read RSSI -->membaca RSSI SIM (kekuatan signal)
[n] get Network status -->membaca status jaringan
[v] set audio Volume -->mengatur Volume Audio dalam persen 1 - 100
[V] get Volume -->membaca status Volume Audio saat ini
[H] set Headphone audio (FONA800 & 808) -->mengatur Volume audio Headset+Mic port
[e] set External audio (FONA800 & 808) -->mengatur Volume audio Loud Speaker+Builtin MIC
[T] play audio Tone -->Memainkan Audio/Ringtone melalui port Speaker
[P] PWM/Buzzer out (FONA800 & 808) -->memainkan nada/tone (dalam frekuensi/PWM)
[f] tune FM radio (FONA800) -->mengatur frekuensi Radio FM
[F] turn off FM (FONA800) -->Mematikan fungsi Radio FM
[m] set FM volume (FONA800) -->mengatur volume Radio FM dalam level 1-6
[M] get FM volume (FONA800) -->membaca status level Volume Radio FM sekarang
[q] get FM station signal level (FONA800) -->membaca kekuatan signal Radio FM pada freq tertentu
[c] make phone Call --> Membuat panggilan telefon ke nomor lain
[A] get call status --> Membaca status panggilan telefon saat ini
[h] Hang up phone -->Mengangkat panggilan telefon masuk
[p] Pick up phone -->Menutup telefon
[N] Number of SMSs -->Menghitung jumlah SMS dalam SIM Card
[r] Read SMS # -->Membaca SMS pada urutan slot tertentu
[R] Read All SMS -->Membaca semua SMS yang ada di inbox
[d] Delete SMS # -->Menghapus SMS pada urutan slot tertentu
[s] Send SMS -->Mengirim pesan SMS
[u] Send USSD -->Mengirim kode USSD
[y] Enable network time sync (FONA 800 & 808) -->Mengaktifkan Sinkronisasi waktu pada Jaringan
[Y] Enable NTP time sync (GPRS FONA 800 & 808) --> Mengaktifkan Sinkronisasi dg waktu NTP
[t] Get network time -->Membaca waktu pada jaringan
[G] Enable GPRS -->Mengaktifkan fitur GPRS
[g] Disable GPRS -->Nonaktifkan fitur GPRS
[l] Query GSMLOC (GPRS)
[w] Read webpage (GPRS) -->Membaca halaman internet
[W] Post to website (GPRS) -->Posting ke halaman internet
[S] create Serial passthru tunnel
-------------------------------------
PASTIKAN SERIAL MONITOR ARDUINO IDE ANDA NAMPAK SEPERTI DIBAWAH INI :
Pastikan Basic Test OK kemudian disusul dengan
+CPIN : READY
Call Ready
SMS Ready
Cara menggunakan Program ini adalah "Anda hanya perlu mengetikan abjad/huruf sesuai perintah
pada menu yang tampil pada serial monitor.
Misalnya untuk membaca SSID anda cukup ketik huruf C pada serial monitor kemudian Enter
Misal untuk mengirim SMS ketik huruf s kemudian akan dilanjutkan dengan instruksi pengetikan nomor tujuan dan isi SMS.
SELAMAT MENGEKSPLOR MODULE SIM ANDA..
Posted On : Wednesday, February 1, 2017Time : 6:12 PM
templatenya bagus banget
ReplyDelete